Nokia CC100 Bedienungsanleitung

CC100User GuideCC100 User Guidewww.netcomm.com.au

CC100 Master Bridge User’s Guide System Setup (TCP/IP Properties) The main window contains the left sub-window for the items to be configured, and

CC100Master Bridge User’s Guide Figure 4: EP Management Architecture Firmware/Driver Files CC100 flash ROM is capable of storing the following file

CC100 Master Bridge User’s Guide Each row represents one EP. Here we have one Master (Local) HCNA device (on the top) and 4 extra Slave EP devices sh

CC100Master Bridge User’s Guide Clicking on the ‘Test’ button can diagnose the noise of HCNA itself and the physical connection quality between Master

CC100 Master Bridge User’s Guide Clicking the ‘Apply’ button will change the Master row background color to yellow (refer to ‘Profile Status’). Pick

CC100Master Bridge User’s Guide After the upgrade has been completed, press Refresh to update the EP management page. Here we have one banned EP show

CC100 Master Bridge User’s Guide Master Privacy Mode EP Privacy Mode On Off On 9 (Key m ch) at 8 (Key not match) 8 Off 8 9(factor

CC100Master Bridge User’s Guide Master/Smart EP Ethernet Properties (Ether) The Ethernet properties of the Master device and Smart EP device are confi

CC100 Master Bridge User’s Guide LAN1LAN2HCNAmax.In Ratemax. InRatemax. Out RateLAN1LAN2HCNAmax. OutRatemax. OutRatemax.InRateEP UpstreamBandwidth Con

CC100Master Bridge User’s Guide IGMP v2 Snooping Setup Supports IGMP V2/V1 snooping only. Shut it if IGMP V3 is adopted in the network. Tag VLAN Se

SSTTA SATSTTETAEMATMETEENEMNTMETENNTTThis device complies with Part 15 of the FCC Rules. This device complies with Part 15 of the FCC Rules. Opera

CC100 Master Bridge User’s Guide The following diagram denotes the path for tagged packets according to the above settings, Second example, enable

CC100Master Bridge User’s Guide Status and Statistics Show port LAN1/LAN2/HCNA Ethernet switch port link status and port statistics. Reset to Defau

CC100 Master Bridge User’s Guide Connect only one EP to Master, with 30dB attenuator add-on. Here’s the ‘Noise Test’ result of the connected EP, P

CC100Master Bridge User’s Guide This diagnosis runs the downstream test from CC100 toward the EP. Also the result of ‘Rx Diagnose’ of the same gears

CC100 Master Bridge User’s Guide Administrator For each account, 3 levels of privilege are provided: Superuser, Read, and ReadWrite. The unchangeable

CC100Master Bridge User’s Guide ( Incoming Source IP Address & Subnet Mask ) = ( IP Address & Subnet Mask ) For the factory default setting,

CC100 Master Bridge User’s Guide Telnet/Http/SNMP Setup 23

CC100Master Bridge User’s Guide Specify that if the built-in Telnet server, Web server, and SNMP agent is enabled or not and assign the port number f

CC100 Master Bridge User’s Guide System Time In order to provide correct timestamp for Syslog event, the CC100 supports SNTP protocol and you may as

CC100Master Bridge User’s Guide We bind MAC address 00-60-64-12-34-56 to port LAN1 and MAC address 00-60-64-78-90-00 to port LAN2, Reboot System Reb

TableofContentsINTRODUCTION...

CC100 Master Bridge User’s Guide Open the ‘EP Management’ window, click on the ‘Refresh’ button first to scan all connected EPs, In the example, t

CC100Master Bridge User’s Guide A count-down counter for entering the uploading mode, Click the ‘Continue’ button to proceed, 28

CC100 Master Bridge User’s Guide Click the ‘Browse’ button to locate the new system firmware at your PC, then click the ‘Start’ button to upload the

CC100Master Bridge User’s Guide Another count-down counter to verify the integrity of the uploaded file, Verifying is ok, click the ‘Continue’ but

CC100 Master Bridge User’s Guide You may activate the new system firmware right away, or wait for the proper scheduled time in order not to disturb

CC100Master Bridge User’s Guide If you don’t upload ‘System Firmware’ first, the ‘Upload Area’ is blank, Activate the New System Firmware Clicking

CC100 Master Bridge User’s Guide A progress counter for upgrade of the CC100 system firmware, CC100 will reboot after upgrade has completed, New sys

CC100Master Bridge User’s Guide Follow the similar steps to upgrade the system firmware. New HCNA driver version ’2.7.5-4’ shown on the ‘Informat

CC100 Master Bridge User’s Guide Also shown on ‘EP Management’ window (‘Upload Area’), Upgrade the New HCNA Driver Designate the targeted Master/EP

CC100Master Bridge User’s Guide Then ‘Upgrade’ button again to confirm, Upgrade EP’s one by one, keep the Master (Local) for the last, Master/EP r

CC100 Master Bridge User’s Guide 1 1 IINNTTRROODDUUCCTTIIOONN This chapter describes the features of your HomePNA3.1 over Coax MDU Master Bridge --

CC100 Master Bridge User’s Guide Indicate the new driver version ‘2.7.5-4’ is working. System Firmware and HCNA Driver Version after Upgrade As shown

CC100Master Bridge User’s Guide Use Telnet Any popular Telnet client could use it to configure the bridge remotely. For example, run Windows built-in

CC100 Master Bridge User’s Guide Note that Telnet connection will be terminated automatically if the telnet client doesn’t input any command for 5 m

CC100Master Bridge User’s Guide 40 dconfig Dump all configurations/settings. default Reset all settings to factory default, except Password. diag

CC100 Master Bridge User’s Guide 41 [-n <allow/deny>] [-p <allow/deny>] ] -t: telnet -w: http/web -n: snmp -p: reply to ICMP ping

CC100Master Bridge User’s Guide 42 help Display all commands with brief description hpnareboot Reset Master HCNA device’ ipconfig [-a <ip>

CC100 Master Bridge User’s Guide 43 <wcomm>: SNMP system read-write community name, default ‘private’

CC100Master Bridge User’s Guide 44 snmptrapserver [-s <set> [-c <act/deact>] [-p <port>] [-a <ip>] [-m <community>] ] D

CC100 Master Bridge User’s Guide 45 [-c <lan1/lan2/off/del>] addresses can be setup, refer Static MAC <mac>: max 8 entries <lan1/la

CC100Master Bridge User’s Guide Use SNMP The SNMP Agent resides in CC100 and will handle requests from a remote SNMP Manager. The CC100 SNMP agent sup

CC100Master Bridge User’s Guide 2 2 IINNSSTTAALLLLAATTIIOONN This chapter describes the installation procedure for your bridge. Packing List Your p

CC100 Master Bridge User’s Guide 47

CC100Master Bridge User’s Guide 4 48 AADDVVAANNCCEEDD FFEEAATTUURREESS This chapter describes the advanced features offered by your bridge. QoS Qu

CC100 Master Bridge User’s Guide 49 A SSPPEECCIIFFIICCAATTIIOONNSS NETWORK INTERFACE ¾ HomePNA3.1 over Coax(HCNA) Compliant ¾ IEEE 802.3u 100Mbps

CC100Master Bridge User’s Guide 50 TRANMISSION SPEED AND RANGE ¾ Up to 144Mbps ¾ Min Attenuation to Endpoint: 12dB ¾ Max Attenuation to Endpoint:

CC100 Master Bridge User’s Guide 51 Legal & Regulatory Information This manual is copyright. Apart from any fair dealing for the purposes of pri

CC100Master Bridge User’s Guide 52 GNU General Public License This product includes software code that is subject to the GNU General Public License

Product WarrantyNetComm products have a standard 12 months warranty from date of purchase. However some products have an extended warranty option, via

CC100 Master Bridge User’s Guide Connecting the Cables To establish a new coax networking system through the CC100, reroute the CATV/Antenna signal s

CC100Master Bridge User’s Guide You can also use other Combiner’s or Mixer-Splitter’s with the CC100 to build the same system. See the following Figu

CC100 Master Bridge User’s Guide Installing the CC100 with an amplifier TV Signal Amplifiers may cause interference when used in conjunction with thi

CC100Master Bridge User’s Guide 3 6 CCOONNFFIIGGUURRAATTIIOONN This chapter describes the configuration procedure for your bridge. Configuration M